/ BGW /

BGW VX660 AMPLIFIER

> Designed for Contractors & Fixed Installations
> 660W per Channel
> 110 dB Signal to Noise Ratio

 


Unprecedented Speed, Control and Low Noise

Designed for contractors, this new series offers a conventional power supply for high reliability and value. This power supply contains over 124,000uF of energy storage to ensure that BGW bass response. Power ranges from 725 watts to 1500 watts per channel at 4 ohms and 200 watts to 1400 watts at 70 volts (no autoformers required) in three models.
BGW’s legendary modular design allows for less down time if there is a problem. Created with the contractor for the contractor, the 1dB precision stepped attenuators are on the rear panel where contractors like them. The VX Series is the ideal for use in fixed installations where the highest sound quality and reliability are a must.

Topology
Class AB with fully balanced differential design; 4-quadrant input stage, current feedback and dual DC Servos.

Warranty
3 years standard warranty

Description

The BGW VX660 is designed for contractors, this new series offers a conventional power supply for high reliability and value. This power supply contains over 124,000uF of energy storage to ensure that BGW bass response. Power ranges from 725 watts to 1500 watts per channel at 4 ohms and 200 watts to 1400 watts at 70 volts (no autoformers required) in three models.
BGW’s legendary modular design allows for less down time if there is a problem. Created with the contractor for the contractor, the 1dB precision stepped attenuators are on the rear panel where contractors like them. The VX Series is the ideal for use in fixed installations where the highest sound quality and reliability are a must.

The BGW VX660 uses barrier strip and monitor speaker output connectors. It has up to 1500 Watts per channel and a 110dB signal to noise ratio.

View all BGW products here.

Follow us on Facebook

Specifications

Input

Connectors
Balanced XLR

Attenuation
One 21 position detented rotary control precision input attenuator per channel. One (1) dB attenuation steps.

Input Impedance
11 kΩ

Input Sensitivity
0.775 Vrms for rated 8 ohm output

Gain
33.4 dB

Polarity
XLR Pinout (Pin 1 = Ground, Pin 2 = Positive, Pin 3 = Negative,)

Dimensions & Power

Dimensions
478mm x 482.5mm x 133.4mm (LxWxH)

Mass
Weight Up to 27kg

Power Requirements
6.7 A @ 230V AC 50-60 Hz

Output

Output Power
660 W/ch @ 8Ω (Stereo Mode)
1050 W/ch @ 4Ω (Stereo Mode)
1500 W/ch @ 2Ω (Stereo Mode)
1750 W/ch @ 8Ω (Bridged Mono)
2450 W/ch @ 4Ω (Bridged Mono)

 

FTC
(Continuous Average Power Rating 20Hz – 20kHz @ .05 THD or less)EIA
(Continuous Maximum Power Rating 1kHz @ 1% THD)CEA
(Instantaneous Peak Power Rating – 1kHz @ 1% THD) 

Distortion
Typical THD<0.008%
Maximum THD 1.0%
IMD<0.008%

Slew Rate
20 V/µs (Stereo Mode)
40 V/µs (Mono Mode)

Damping Factor
>300:1 (ref. 8Ω)

Crosstalk
>90 dB @ 20 Hz – 20 kHz

DC Offset
<10 mV (5 mV typical)

Recommended load
4/8 Ω

Frequency Response
8 Hz – 56 kHz, +0/-3 dB
20 Hz – 20 kHz, +0/-0.3 dB

Signal-to-Noise Ratio
>110 dB referenced to rated output (A-Weighted)

Speaker Outputs
Barrier Strip